Description
The USA Lab Farmer-200 is a turnkey ethanol centrifuge extraction system that allows users the ability to extract botanical compounds to achieve superb results and separation while maintaining a closed loop system. The Farmer-200 takes 7-18 gallons of alcohol per batch and 10-20lbs of biomass per batch for approximately 200lbs of dry material per 8 hour shift with a single operator. Ethanol is loaded into the initial solvent tank via a diaphragm pump. The ethanol is then pumped through the centrifuge where an agitation cycle begins. After the agitation cycle, the outlet valve is opened and the spin dry cycles can begin. The ethanol & oil mixture is now pumps via a diaphragm pump into an additional solvent tank, and recycled 3-8 times depending on SOP. Upon final cycle, solution is pumped through a diaphragm pump into a lenticular filter via a 0.8Micron Pak filter and 7-10psi of differential pressure for a whopping 200-300gal per hour flow rate. Solution is fed into a final keg which can be further processed to users SOP. Common practice is to feed into our dual explosion evaporator for 8-10 Gallons per hour recovery rate of ethanol. Ethanol is then fed into kegs for recovery. These kegs can then be re-used at this step. Oil is then fed into our 50L SS reactor for decarb and then further processed via our 12L USA Made glass short path kit.
FARMER-200 PACKING LIST | |
STORAGE VESSELS | |
USA Lab 200LB Jacketed Solvent Tanks | 2 |
200LB Solvent Tank Parts | |
-1/2″ MNPT to 1/2″ MNPT Hex | 6 |
-1/2″ Superlok Ballvalve (Inlet, Outlet, and Drain) | 6 |
-1/4″ Superlok Ballvalve (Nitrogen) | 2 |
-1/2″ MNPT to 1/4″ MNPT Hex | 2 |
-1/4″ MNPT to 1/4″ MJIC | 2 |
-1/2″ MNPT to 1/2″ Barb | 10 |
-1/4″ MNPT Gauge | 2 |
-1.5″ End Cap (Optional for Drain) | 1 |
-1.5″ TC x 12″ Bottom Drain | 2 |
-1.5″ TC to 1/2″ FNPT | 2 |
-1.5″ Buna Gasket | 2 |
-1.5″ High Pressure Triclamp | 2 |
-1/2″ MNPT Plug | 2 |
USA Lab 50L Kegs (1 For Storage After Filter) | 1 |
50L Keg for Storage Parts | |
-1.5″ Meta Sight Glass | 2 |
-1.5″ TC to 1/2″ FNPT | 1 |
-2″ TC to 1/2″ FNPT | 1 |
-1.5″ Buna Gasket | 1 |
-2″ Buna Gasket | 1 |
-1.5″ Single Hinge Triclamp | 3 |
-2″ Single Hinge Triclamp | 1 |
-6″ Buna Gasket | 1 |
-6″ Single Hinge Triclamp | 1 |
-1/4″ MNPT Gauge | 1 |
-1/2″ MNPT Plug | 2 |
-1/2″ MNPT to 1/4″ MNPT Hex | 1 |
-1/2″ MNPT to 1/2″ MNPT Hex | 3 |
-1/2″ Superlok Valve | 3 |
-1/4″ Superlok Valve (Nitrogen) | 1 |
-1/2″ MNPT to 1/2″ Barb | 3 |
-1/4″ MNPT to 1/4″ MJIC | 1 |
USA Lab 30L -80°C Chiller – DLSB-30/80 (For Pre Extraction Vessel) – 2x 11FT 1/2″ Hose | 1 |
USA Lab 30L -40°C Chiller – DSLB-30/40 (For Post Extraction Vessel) – 2x 11FT 1/2″ Hose | 1 |
XTC-20 CENTRIFUGE | |
USA Lab 20L XTC-20 Ethanol Centrifuge | 1 |
USA Lab XTC Control Panel | 1 |
USA Lab 30L -40°C Chiller – DLSB-30/40 (For Centrifuge Jacket) – 2x 11FT 1/2″ Hose | 1 |
20L 100 Micron Mesh Bags | 2 |
12-3 Gauge 20Ft Wire | 1 |
Top of Centrifuge 3 Way | |
-1.5″ TC to 1/2″ FNPT | 1 |
-1.5″ Buna Gasket | 1 |
-1.5″ Single Hinge Triclamp | 1 |
-1/2″ FFM 3-way Stree Tee | 1 |
-1/2″ MNPT to 1/2″ MNPT Hex | 2 |
-1/2″ Superlok Valves | 2 |
-1/2″ MNPT to 1/2″ Barb | 2 |
Centrifuge Drain Assembly | |
-2″ TC to 1/2″ FNPT | 1 |
-2″ Buna Gasket | 2 |
-2″ Single Hinge Triclamp | 2 |
-2″ TC Ball valve | 1 |
-1/2″ MNPT to 1/2″ Barb | 1 |
Centrifuge Fluid Jacket Assembly | |
-1.5″ TC to 1/2″ FNPT | 2 |
-1.5″ Buna Gasket | 4 |
-1.5″ Single Hinge Triclamp | 4 |
-1.5″ TC Ball valve | 2 |
-1/2″ MNPT to 1/2″ Barb | 2 |
LENTICULAR FILTER | |
USA Lab 12″ 2 Stack Lenticular Filter | 1 |
12″ Filters PAK | 2 |
1.5″ TC Ball Valve | 2 |
1.5″ TC to 1/2″ FNPT | 2 |
1.5″ Buna Gasket | 4 |
1.5″ Single Hinge TC | 4 |
AIR COMPRESSOR | |
California Air Tools 10020C Air Compressor | 1 |
5-way Manifold for Air Compressor | 1 |
California Air Tools 317 Water and Oil Air Filter | 1 |
(1 Pre-assembled on Filter, 5 Pre-assembled on Hose) 1/4″ Air Plug to 1/4″ FNPT | 6 |
(Pre-assembled on Filter) 1/4″ MNPT to 1/4″ Coupler | 1 |
(Pre-assembled on Hose) 1/4″ FNPT to 1/4″ Coupler | 5 |
3/8″ 300psi 25ft Air Compressor Hose | 5 |
Aro Diaphragm Pumps with 1/4″ Inlet and 1/2″ Barb Fluid Inlet & Outlet | 4 |
EXRDS-1050-VB-TK | |
USA Lab 50L -30°C Chiller (For EXRDS-1050 Turnkey) | 2 |
USA Lab 50L dual Explosion-Proof Rotary Evaporator | 1 |
MD 4C NT Vacuumbrand Vacuum Pump (For EXRDS-1050 Turnkey) | 1 |
USA Lab 50L Kegs (for EXRDS-1050 Collection) | 2 |
50L Keg for Drainage | |
-1.5″ Meta Sight Glass | 4 |
-1.5″ TC to 1/2″ FNPT | 2 |
-2″ TC to 1/2″ FNPT | 2 |
-1.5″ Buna Gasket | 2 |
-2″ Buna Gasket | 2 |
-1.5″ Single Hinge Triclamp | 6 |
-2″ Single Hinge Triclamp | 2 |
-6″ Buna Gasket | 2 |
-6″ Single Hinge Triclamp | 2 |
-1/4″ MNPT Gauge | 2 |
-1/2″ MNPT Plug | 4 |
-1/2″ MNPT to 1/4″ MNPT Hex | 2 |
-1/2″ MNPT to 1/2″ MNPT Hex | 6 |
-1/2″ Superlok Valve | 6 |
-1/4″ Superlok Valve (Nitrogen) | 2 |
-1/2″ MNPT to 1/2″ Barb | 6 |
-1/4″ MNPT to 1/4″ MJIC | 2 |
3 Way 1/2″ Tee for Vacuum Line | 2 |
10ft Vacuum Hose | 2 |
50L DECARB REACTOR | |
USA Lab 50L SS Reactor Storage Vessel | 1 |
1/2″ MNPT to 1/2″ MNPT Hex (For Fluid Jacket) | 2 |
50L Reactor 12″ Hemispherical Lid Assembly | |
-12″ TC Hemispherical Lid – 2x 2″TC, 1x 3″TC, 2x 1/2″ FNPT, 2x 1/4″ FNPT | 1 |
-3″ End Cap with Hole for Stirring Rod | 1 |
-2″ Meta Sight Glass | 1 |
-1/4″ MNPT Bottom Mount Gauge | 1 |
-1/2″ Superlok Valves | 2 |
-1/2″ MNPT to 1/2″ MNPT Hex | 2 |
-1/2″ MNPT to 1/2″ Barb | 2 |
-1/4″ Plug | 1 |
-2″ End Cap With Stir Motor Rod Mount | 1 |
-2″ Buna Gasket | 1 |
-3″ Buna Gasket | 1 |
-12″ Buna Gasket | 1 |
-2″ High Pressure Triclamp | 2 |
-3″ High Pressure Triclamp | 1 |
-12″ High Pressure Triclamp | 1 |
50L Reactor 6″ Hemispherical Bottom Assembly | |
-6″ TC to 1/2″ FNPT Hemi Reducer | 1 |
-1/2″ MNPT to 1/2″ MNPT Hex | 1 |
-1/2″ Superlok Valve | 1 |
-1/2″ MNPT to 1/2″ Barb | 1 |
-6″ Buna Gasket | 1 |
-6″ High Pressure Triclamp | 1 |
Air Motor Assembly | |
-1HP Air Motor | 1 |
-36″ 1/2″ Shaft with 4″ 3 Paddle Attached | 1 |
-4″ 3 Paddle With Bore Through | 1 |
-Heavy Duty Motor Clamp | 1 |
USA Lab 30L 200°C Heater – RH30 (For 50L Vessel Jacket) – | 1 |
12L USA MADE GLASS TURNKEY KIT | |
USA Lab 12L USA Made glass Short path kit | 1 |
USA Lab UVP-21 21 CFM Vacuum Pump | 1 |
USA Lab -10°C to 100°C Heater Chiller | 1 |
USA Lab 12L Heating Mantle | 1 |
USA Lab Digivac Vacuum Gauge | 1 |
OTHER ITEMS | |
USA Lab 55Gal Glycol | 1 |
USA Lab 5Gal Inland 19 Oil | 1 |
1/2″ Silicone Hosing – 75FT | 1 |
USA Lab -40 10CuFt Freezer | 1 |
Device | Plug Style | Min Voltage | Breaker Amps | Amps Peak | Amps Nominal | Watts |
XTC-20 Centrifuge | Hardwired | 240V 3ph | 15 | ~7 | 6 | 2200 |
XTC-20 Phase Converter (optional) | Hardwired | 220V | 40 | 40 | ||
RH-30L Heater | L6-30p | 220V | 30 | ~24 | 23 | 5000 |
30/80 Chiller | L6-30p | 220V | 30 | ~32 | 24 | 5250 |
30/40 Chiller | L6-30p | 220V | 30 | ~20 | 12 | 2500 |
30/40 Chiller | L6-30p | 220V | 30 | ~20 | 12 | 2500 |
50/30 Chiller | L6-30p | 220V | 30 | ~22 | 13 | 2800 |
50/30 Chiller | L6-30p | 220V | 30 | ~22 | 13 | 2800 |
50L Dual Roto | L6-30p | 220V | 30 | ~30 | 30 | 6600 |
UVP-21 Vacuum pump | 6-15p | 220V | 15 | ~7 | 5 | 1100 |
Vacuubrand pump | 5-15p | 110V | 15 | ~5 | 3 | 250 |
2HP Compressor | 5-15p | 110V | 15 | ~20 | 14 | 1540 |
ZNCL Heating Mantle | 5-20P | 110V | 20 | ~20 | 20 | 2200 |
HC-5/10 Heater Chiller | 5-20p | 110V | 30 | ~26 | 22 | 2400 |
10 Cuft Cryo Freezer | 5-15p | 110V | 15 | 15 | 1100 | |
Total Amperage and Wattage | 375 | 38240 |
For Technical Support, Questions, or Other Issues Please Email or Call Us!
Reviews
There are no reviews yet.